Seagull Models GROB TUTOR G115 Specifications

1www.seagullmodels.comASSEMBLY MANUALMS:144Specifications:Wing span -------------------------66.9in (170.0cm)Wing area --------------548.7sq.in (35.4s

GROB TUTOR G115 Instruction Manual.10 4) Test fit the stopper assembly into thetank.

11www.seagullmodels.comFuel tank.8) Use plywood template to hold in place thefuel tank with C/A glue to secure the fuel tankinside the fuselage.9) U

GROB TUTOR G115 Instruction Manual.122) Use a pin drill and 2mm drill bit to drill asm

13www.seagullmodels.com5) Slide the pushrod tube in the firewall andguide it through the fuel tank mount. Usemedium C/A to glue the tube to the firew

GROB TUTOR G115 Instruction Manual.1435411531Screw..4-5mm.LANDING GEAR INSTALLATION:A.

15www.seagullmodels.com4252) Install landing gear at the top Fuselage.Adjustable connector.M2 clevis.Screw..

GROB TUTOR G115 Instruction Manual.16Trim and cut.5mm. 2) Install lights at the top C

17www.seagullmodels.comC/A glue. 4) Install the muffler and muffler extensiononto the engine and make the cutout in thecowl for muffler clearance.

GROB TUTOR G115 Instruction Manual.183) Attach the motor to the front of the electricm

19www.seagullmodels.comBalsa sticks135mm.4) Locate the plywood battery tray to thefuselage. Tighten the screws using machinescrews M3x15mm to secure

GROB TUTOR G115 Instruction Manual.2INTRODUCTION.Thank you for choosing the GROB TUROR

GROB TUTOR G115 Instruction Manual.204) Apply 2-3 drops of thin C/A to each of themoun

21www.seagullmodels.com8) A string has been provided in the wing topull the aileron lead through to the wing root.Remove the string from the wing at

GROB TUTOR G115 Instruction Manual.22Snap keeper.Servo arm.3) Connect the linkage as s

23www.seagullmodels.comRepeat the procedure for theaileron servo.WHEEL AND WHEEL PANTS.wheel collar.wheel.Axle.Washer.M3.M3. 1) Assemble and mou

GROB TUTOR G115 Instruction Manual.24Draw center line. 2) Using a modeling knife, car

25www.seagullmodels.com 6) With the stabilizer held firmly in place,use a pen and draw lines onto the stabilizerwhere it and the fuselage sides meet.

GROB TUTOR G115 Instruction Manual.26ELEVATOR PUSHROD HORNINSTALLATION. 1) Install t

27www.seagullmodels.comElevator control horn.Rudder control horn. 4) Elevator and rudder pushrods assemblyas pictures below. 3) Thread one clevis

GROB TUTOR G115 Instruction Manual.28INSTALLATION PILOT.1) A scale pilot is included w

29www.seagullmodels.com- Apply a bead of canopy glue around the insideedge of the canopy. Position the canopy ontothe hatch. Use tape to hold the cano

3www.seagullmodels.comKIT CONTENTS.1 Fuselage2 Canopy3 Left wing panel4 Right wing panel5 Tail set6 Aluminum wing tube7 Scale pilot8 Seat (

GROB TUTOR G115 Instruction Manual.30 Insert two wing panels as pictures below.ATTAC

31www.seagullmodels.comBALANCING.  1) It is critical that your airplane bebalanced correctly. Improper balance willcause your plane to lose control

GROB TUTOR G115 Instruction Manual.32 D) Check the throttle. Moving the throttlestick

GROB TUTOR G115 Instruction Manual.4The control surfaces, including theailerons, elevat

5www.seagullmodels.com 4)Deflect the aileron and completelysaturate each hinge with thin C/A glue. Theailerons front surface should lightly contact

GROB TUTOR G115 Instruction Manual.63) Once the epoxy cures and use a coveringiron to s

7www.seagullmodels.comINSTALL THE AILERONS CONTROLHORN.2 sets.3x35mm.Masking tape.Sealing iron.1) Locate the hardware necessary to installthe control

GROB TUTOR G115 Instruction Manual.8 Install the elevator control horn using thesame me

9www.seagullmodels.comRepeat steps to install the rudder control hornas same as steps done for ailerons. INSTALL RUDDER CONTROL HORN.1 sets.3x30mm.3m